FLUKE 187 MUTLIMETER

• TRUE RMS
• Resistor [from 0,01 Ohm - 500 M Ohm]!
• Capacitor [1pF - 50.000µF]
• Temperature [(-200°) - (+1350°)
• Conductance 0,01nS - 500nS
• dBm and dBV from -52 to +60dB
• Voltage 1µF - 1000V  (DC and AC)
• Current 0,01µA - 10A(DC and AC)
• blue Backlight
• min max / rel
• 50.000 digits
• Frequency 0,01Hz - 1MHz

I like this Multimeter! Looks great, many digits, nice backlight. You could measure DC and it shows DC and AC and vice versa. The 180 series can measure dBm and BV! Lifetime warranty on parts.

METEX MS-9150 Multi Measurement Station

This is a compact laboratory tool. It has an 4 parts integrated:

• Power Supply 15V, 5V and 0-30V with LCD Display
  GND free or grounded, current and voltage adjustable
  shows voltage or current in display
   
• Multimeter (Metex type) TRUE RMS Multimeter 3 3/4 digit LCD double display with bar graph and back-lighting. Automatic range selection with Min./Max. save, Data-Hold and REL function. DC V: 0.1 mV ... 1000 V at ± 0.3% + 1 digit AC V (TRUE-RMS): 0.1 mV ... 750 V at ± 1% + 3 digit DC A: 10 µA ... 20 A at ± 0.8% + 1 digit AC A (TRUE-RMS): 10 µA ... 20A at ± 2.5% + 3 digit R: 1 W ... 40 MW at ± 0.5% +1 digit L: 10 µH ... 400 mH at ± 3% + 10 digits C: 1 pF ... 400 µF at ± 3% +5 digits In addition, acoustic continuity tester, plus diode and logistic test function. Built-in RS 232 interface.
   
• Function Generator Wave forms: sinusoid, rectangular, triangle, ramps, pulses, TTL · frequency range: 1 Hz - 10 MHz (7 ranges) · Output impedance: 50W ±10%, 600 W ± 10% · Amplitude: 2 Vpp-20 Vpp · Attenuator: -20 dB
   
• Universal Counter  LED Frequency meter: 8 digit LED display with switched peak times of 0.1, 1 and 10 seconds. Measurement range 5 Hz to 1.3 GHz. Inputs A/B: 5 - 100 MHz · Sensitivity 20 mV · Input resistance 1 MW/100 pF · Representation of functions A + B, A - B and A/B · Switchover option to period measurement. Input C: 100 MHz to 1.3 GHz · Sensitivity 20 mV · Input impedance 50W

LABORATORY POWER SUPPLY PS-2403D

Nice Power Supply. 2x 0-40V. You can combine the supplies to one unit (=80V output). Sometimes you need the +48V Phantom Power for testing ;-)
Output voltage and current continuously variable. This electronically-regulated, dual-voltage power supply in a plastic casing is ideally suited for education, hobbies, the workshop and model building.By means of series or parallel switching, up to 80 V/3 A or 40 V/6 A can be drawn from the device. Naturally, this power supply has short circuit protection and is VDE approved.Specifications: Input voltage 230 V~/ 50 Hz · Output voltage 2 x 0 - 40 V DC, continuously variable, switched in series 0 - 80 V= · Output current 2 x 0.02 - 3 A, continuously variable, switched in parallel 6 A · Voltage stability at ± 10% fluctuation in rated voltage £ 0.05% · At 100% load variation £ 10 mA · Residual ripple approximately 2 mV RMS · Dimensions (W x H x D) 310 x 135 x 260 mm · Weight approximately 9 kg · Supplied with instructions. Mains cable not included.

HAMEG 203 2 channel 20Mhz Oscilloskope

The HAMEG HM203 is sold over 180,000 times worldwide. The bandwidth20MHz. It is a 2 channel osciloskope. It has an integrated component tester.It is the same model which i learned in my profession. Ok i would like to have an teletronix colour display 4 channel oscii... but i think i won’t really need it...

Here is a link to a virtual hameg 203: http://www.virtuelles-oszilloskop.de/

Desoldering Stations (Weller/Cooper Tools)

This is my Weller desolder station. (there a 2 shown on my picture) It has a power supply for a standard weller soldering iron AND a desoldering iron. Both are temperature controlled. The vakuum unit is integrated.

I also own 2 ersa soldering stations, 1 weller WTCP station and gas-soldering irons (pyropen).

Isolation Transformator

[foto trenntrafo]

When iam working on high voltage circuits with tubes... i use this trafo. It isolates the GND/PE. But it only works of course when you’re using only “ONE-HAND” in the circuit ;-) I like this thing because it saves my life!

PCB drilling maschine

Little maschine nice for drilling the holes in pcbs. A must have. It’s not so expensive.. look @ ebay ;-)

ISEL etching device

For small pcb series.

Sorting cases

(foto sortierkästen)

Here are some of my components. I like these sorters.